Cleaning method of vape RTA/RDA/RBA coils
Fancy silk is made of many heating wires, which is larger than ordinary heating wire in heating area. So it's going to be better than regular heating silk in terms of taste or smoke.
Hot silk just came out, as the winding process complex, so many players can only look at silk sigh. With the development of e-cigarette industry, there are a lot of different materials at present, which have been wrapped into heat coil fancy silk, commonly known as fancy finished silk. Make it easier for players to experience the VAPE experience brought by fancy silk.
In fact, a few days after the use of fancy silk, more or less there will be carbon deposition on the surface of the silk, in addition to look very unappetizing, but also affected taste, in the suction, always a little bit of burnt mushy. What follows is that players often do to clean the hot wire and replace the cotton.
But actually, when the design silk cleans, still has many places to be worth our attention. Today, the author for you briefly said.
Above is the three core clapton fancy silk of NI80 material for 4 days, which is in the condition of heating wire without cleaning. You can see that there's a lot of carbon deposition, and the hot filaments are obviously black out.
Smoke, can have more apparent mushy flavour. Of course, this is also to show the effect, the author recommends, or 1-2 days clean and replace the cotton.
Carbon deposition can even be blown up due to high temperature, and then adhered to the inner wall of the atomizing chamber.
Remove the cotton and install the atomizer on the host. As you burn the wire, then set the voltage to about 3.0v. (the author use the resistance is 0.16 Ω, power to 55 w).
Don't turn the power too high, because if you heat it up at high temperature, it will explode and burn your hands. It may also cause the entire filament to fuse.
While heating, a strong smell of burnt mush is produced by the carbon deposition on the surface of the hot filament.
After heating silk burns red, it can be seen that the carbon deposition piece adheres to the surface of heating silk like scab.
After burning wire, can let go of the ignition key, and then can be heat wire into the warm water (water temperature about 40 to 60 °). Be careful that the main engine can not touch the water.
Remember - don't turn it on, Otherwise, the hot wire will be burned directly in the water and then fuse due to a short circuit.
So why it shoule be the warm water?
In fact, the red-hot wire is put into water, and the heat treatment process of this rapid cooling process is called quenching.
If the temperature difference between water and the heater is too large, the heater will be brittle, that is, the heater will break easily.
Directly affects the service life of heating filament.

After repeated "quenching", it can be seen that there are quite a few black particles of carbon deposition in the water.
Then we can use the brush to clean the hot wire. Remove the carbon accumulated in the fine space between the silk and the silk.
This brush bristles with both stainless steel and brass, and stainless steel is harder.

When washing, be sure to pay attention to the following 2 points.
1. be gentle and careful, do not wash it too hard, because the outsourcing silk of the heating wire is usually relatively fine, and if the force is too strong, it will easily hurt the outsourcing silk.
2. be sure to follow one direction. Do not brush back and forth repeatedly. Author habit is from left to right, from top to bottom again, separate twice to wash brush. Because of repeated brush back and forth, the original winding process of the complex silk will be disrupted, resulting in a larger gap outsourcing.
After that, the author likes to separate the whole atomizer and put it into an ultrasonic cleaner for cleaning. Let all kinds of dirt hidden in the atomizer be cleaned out.
The last step is to air dry the atomizer and then install the main engine and adjust the burning. Let the hot filament cool naturally to room temperature.
Actually this step, besides be to adjust heating silk, see if calorific is even besides. There is still a tempering effect. The performance and service life of heating wire can be improved.
Fancy silk brings a higher quality VAPE experience to the players, but the price is more than a fraction higher than normal heating wire due to the material and winding process. While using fancy silk, we should know how to do daily cleaning and maintenance.
Just like a car, you should appreciate it but also know how to maintain it. This will not only extend the service life of fancy silk, but also give it better performance and better experience.